Audio-enhancement TLD100 Manuale Utente

Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use.The model number is

10Operating procedures1 Insert the plug of the supplied AC adaptor into the wall outlet. The operation LED of the sensor/receiver lights green.2 Tu

11The installation should be carried out following local standards for electric products. Warning• Be sure to contact your dealer for installation.

12• Plasma television screens generate infrared interference. It is not recommended to use a plasma display in the same room where the TLD100 is in

13Functions and settings Functions• Microphone override functionThis is a function where the audio level of LINE IN is auto-matically adjusted to lowe

14 About the feedback blockerThis is a function when a feedback loop is generated as the microphone is used in close proximity to a speaker. An integr

15F1 CNT, F2 CNT functionThese functions are available when MTD-09 is used. When F1 or F2 signal is transmitted from the microphone, it will active F

16F2 ACK functionWhen an F2 ACK signal is received, the reception LED indicator of this unit (CH1 or CH2) turns from red to green. When, after turning

17•DIP switch settingNo Name Function On Off1 Microphone Override Selection of microphone override function Activated* Deactivated2 Tone ON/OFF Selec

18•Channel settingRefer to the combination table and set each channel appropriately.This unit can receive only through CH1 and CH2. Therefore, this un

19 Connection of sensor/receiver• LINE IN connectionConnect the audio output of a projector, CD player, DVD/VCR or similar line level output to the L

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These lim

• 20 Connection to control terminal Cable processingBefore connection, prepare the cable as shown in the drawing at right.Note:• Stranded wire is hig

21 Connection of RS-232CThe TLD100 can send and receive commands and status information via RS-232C to external devices. The external device is conne

22 Connection of power supplyThe supplied AC adaptor is connected to the conversion box and the adaptor plug is inserted into the wall outlet after en

23 Reception range and expansionThe reception range of one infrared sensor in normal use is approx. 8 m {26 feet} in radius.To expand the reception ra

24 When connecting multiple Infrared Sensors Warning• Before installing, be sure to turn off the power of the infrared sensor/receiver.There is a

25 About the coaxial cablesUse the following length and type of coaxial cable to connect the infrared receivers and the infrared sensors.• Length of

26Installation Warning• Before installing, be sure to turn off the power of the infrared sensor/receiver. There is a risk of electric shock. Install

27 Warning• Before installing, be sure to turn off the power of the infrared sensor/receiver. There is a risk of electric shock. When not using a ce

28 Installation of the conversion box Warning• Be sure to turn off the power of this unit before installation. Otherwise electric shock may result.1

29 PrefaceThe volume of this unit and functions set by the DIP switch can be remotely controlled by an external device using the serial communication

3Important safety instructions1) Read these instructions.2) Keep these instructions.3) Heed all warnings.4) Follow all instructions.5) Do not use

30 Examples of sequence• Examples are shown below. Refer to the next page or later for further information on command.• For a setting command (a com

31 Command listCommand Content Type 1st parameter 2nd parameter Command exampleQPW Query about this unit power stateQuery None None $QPW[CR][LF]Respon

32Command Content Type 1st parameter 2nd parameter Command exampleSDS Tone setting Setting 2: Tone 0: Disable1: Enable$SDS:2:1[CR][LF]Response Same as

33Symptom Cause/solution Ref. pagesNo reception Does the operation LED light? → Check the AC adaptor connection. Check the connection between the sen

34SpecificationsGeneralPower (DC IN) 24 V DC (use the specified AC adaptor (included))Input current 160 mA (At 4 pieces of extended sensors (EDS-07) c

35InterfaceTO CONVERSION BOX RJ-45 (LAN type connector), * original formatNote: Never make a connection to a LAN connector that is compatible with Eth

Audio Enhancementwww.AudioEnhancement.comFor customer support, call 800.383.936214241 S. Redwood Rd., Bluffdale, UT 84065 U.S.A. © Audio Enhancement,

4Limitation of liabilityTHIS PUBLICATION IS PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, TH

5Precautions• Contact your dealer for installation. Skill and experience are required for installation to avoid risk of fire, electric shock, injury

6FeaturesCONTENTSThis unit is a receiver which integrates both a sensor receiving infrared light from the infrared wireless microphone (MTD-09,MHH-09)

7Caution about interception of transmissionThis product is a wireless system using infrared, and the transmission and reception of audio signals are p

8Major operating controls and their functions (IR-Satellite or Sensor)Front Back① Infrared sensor cover To receive only the infrared by the inner sen

9Major operating controls and their functions (Conversion box)① Receiver connector [TO RECEIVER] This connector, labeled “TO RECEIVER”, is used to c